灌膠機的膠管應該如何更換?
灌膠機的膠管應該如何更換?接下來小編給大家進行簡單的介紹。
How to replace the rubber tube of the glue filling machine? Next, I will give you a brief introduction.
更換粘合劑填充機的軟管是一個非常普遍的問題。每次更換粘合劑時都必須更換橡膠軟管。更換粘合劑填充機的橡膠軟管可確保兩部分式粘合劑填充機的正常運行，并更換粘合劑填充機的軟管。在交換過程中我需要注意什么?
It is a very common problem to change the hose of the adhesive filling machine. The rubber hose must be replaced every time the adhesive is replaced. Replacing the rubber hose of the adhesive filler ensures the proper operation of the two-part adhesive filler and the replacement of the hose of the adhesive filler. What should I pay attention to in the exchange process?
，灌膠機更換膠管的步：
First, the first step of replacing the rubber hose of the rubber filling machine:
關閉自動分配器并打開軟管，從軟管上卸下冷卻套，卸下空氣頭，然后卸下軟管。確保90°彎頭配件也連接到分配閥上。卸下軟管后，分配閥將適配器底部的小腔鎖定。用舊軟管中的凝膠填充空腔，并檢查鎖定適配器中是否有氣泡。如果有氣泡，請用新軟管填充腔體，檢查新軟管是否有新氣泡，如果有氣泡，請使用另一根軟管。
Close the automatic distributor and open the hose, remove the cooling sleeve from the hose, remove the air head, and then remove the hose. Make sure that the 90 ° elbow fitting is also connected to the distribution valve. When the hose is removed, the distribution valve locks the small chamber at the bottom of the adapter. Fill the cavity with the gel in the old hose and check whether there is any bubble in the lock adapter. If there are bubbles, fill the cavity with a new hose, check whether there are new bubbles in the new hose, if there are bubbles, use another hose.
如果我們的灌膠機設備使用年限比較長的話，我們就需要徹底清潔灌膠機的干燥點膠閥或點膠泵，然后再按照上面的灌膠機膠管更換步驟就行更換!
If our equipment has a long service life, we need to thoroughly clean the dry dispensing valve or pump of the dispenser, and then follow the above steps to replace the rubber hose of the dispenser!
以上內容由灌膠機小編整理，本文觀點不代表本站觀點。
The above content is compiled by the glue filling machine. This point of view does not represent this station's point of view.
上一篇：灌膠機不收膠老是滴膠什么原因?
下一篇：雙組份打膠機出膠壓力不足怎么辦？
